Schneider-Electric
 
ATV12H075M2 fotografija – Schneider- web-product-data-sheet
ATV12H075M2
frekv.pretvarač promj.brzine ATV12–0,75 kW–1 ks–200..240 V–1 faza–s hladnjakom
Schneider Electric
Karakteristike
Main
Range of product Altivar 12
Product or component type Variable speed drive
Product destination Asynchronous motors
Product specific application Simple machine
Assembly style With heat sink
Component name ATV12
Quantity per set Set of 1
EMC filter Integrated
Built-in fan Without
Network number of phases 1 phase
[Us] rated supply voltage 200...240 V - 15...10 %
Motor power kW 0,75 kW
Motor power hp 1 hp
Communication port protocol Modbus
Line current 10,2 A 200 V
8,5 A 240 V
Speed range 1…20
Transient overtorque 150…170 % of nominal motor torque depending on drive rating and type of motor
Asynchronous motor control profile Quadratic voltage/frequency ratio
Voltage/frequency ratio (V/f)
Sensorless flux vector control
IP degree of protection IP20 without blanking plate on upper part
Noise level 0 dB
Complementary
Supply frequency 50/60 Hz +/- 5 %
Connector type 1 RJ45 on front face)Modbus
Physical interface 2-wire RS 485 Modbus
Transmission frame RTU Modbus
Transmission rate 4800 bit/s
9600 bit/s
19200 bit/s
38400 bit/s
Number of addresses 1…247 Modbus
Communication service Read holding registers (03) 29 words
Write single register (06) 29 words
Write multiple registers (16) 27 words
Read/write multiple registers (23) 4/4 words
Read device identification (43)
Prospective line Isc 1 kA
Continuous output current 4,2 A 4 kHz
Maximum transient current 6,3 A 60 s
Speed drive output frequency 0,5…400 Hz
Nominal switching frequency 4 kHz
Switching frequency 2...16 kHz adjustable
4...16 kHz with derating factor
Braking torque Up to 70 % of nominal motor torque without braking resistor
Motor slip compensation Preset in factory
Adjustable
Output voltage 200...240 V 3 phases
Electrical connection Terminal 3.5 mm², AWG 12 L1, L2, L3, U, V, W, PA, PC)
Tightening torque 0,8 N.m
Insulation Electrical between power and control
Supply Internal supply for reference potentiometer 5 V DC 4,75…5,25 V), <10 mA overload and short-circuit protection
Internal supply for logic inputs 24 V DC 20,4…28,8 V), <100 mA overload and short-circuit protection
Analogue input number 1
Analogue input type Configurable current AI1 0...20 mA 250 Ohm
Configurable voltage AI1 0...10 V 30 kOhm
Configurable voltage AI1 0...5 V 30 kOhm
Discrete input number 4
Discrete input type Programmable LI1...LI4 24 V 18...30 V
Discrete input logic Negative logic (sink), > 16 V, < 10 V 3.5 kOhm
Positive logic (source), 0...< 5 V, > 11 V
Sampling duration 20 ms +/- 1 ms logic input
10 ms analogue input
Linearity error +/- 0.3 % of maximum value analogue input
Analogue output number 1
Analogue output type AO1 software-configurable voltage 0...10 V 470 Ohm 8 bits
AO1 software-configurable current 0...20 mA 800 Ohm 8 bits
Discrete output number 2
Discrete output type Logic output LO+, LO-
Protected relay output R1A, R1B, R1C 1 C/O
Minimum switching current 5 mA 24 V DC logic relay
Maximum switching current 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay
2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay
3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay
4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay
Acceleration and deceleration ramps Linear from 0 to 999.9 s
U
S
Braking to standstill By DC injection, <30 s
Protection type Line supply overvoltage
Line supply undervoltage
Overcurrent between output phases and earth
Overheating protection
Short-circuit between motor phases
Against input phase loss in three-phase
Thermal motor protection via the drive by continuous calculation of I²t
Frequency resolution Analog input converter A/D, 10 bits
Display unit 0.1 Hz
Time constant 20 ms +/- 1 ms for reference change
Marking CE
Operating position Vertical +/- 10 degree
Height 143 mm
Width 72 mm
Depth 131,2 mm
Net weight 0,8 kg
Functionality Basic
Specific application Commercial equipment
Variable speed drive application selection Commercial equipment Mixer
Commercial equipment Other application
Textile Ironing
Motor starter type Variable speed drive
Environment
Electromagnetic compatibility Electrical fast transient/burst immunity test level 4 EN/IEC 61000-4-4
Electrostatic discharge immunity test level 3 EN/IEC 61000-4-2
Immunity to conducted disturbances level 3 EN/IEC 61000-4-6
Radiated radio-frequency electromagnetic field immunity test level 3 EN/IEC 61000-4-3
Surge immunity test level 3 EN/IEC 61000-4-5
Voltage dips and interruptions immunity test EN/IEC 61000-4-11
Electromagnetic emission Radiated emissions environment 1 category C2 EN/IEC 61800-3 2...16 kHz shielded motor cable
Conducted emissions with integrated EMC filter environment 1 category C1 EN/IEC 61800-3 2, 4, 8, 12 and 16 kHz shielded motor cable <5 m
Conducted emissions with integrated EMC filter environment 1 category C2 EN/IEC 61800-3 2...12 kHz shielded motor cable <5 m
Conducted emissions with integrated EMC filter environment 1 category C2 EN/IEC 61800-3 2, 4 and 16 kHz shielded motor cable <10 m
Conducted emissions with additional EMC filter environment 1 category C1 EN/IEC 61800-3 4...12 kHz shielded motor cable <20 m
Conducted emissions with additional EMC filter environment 1 category C2 EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m
Conducted emissions with additional EMC filter environment 2 category C3 EN/IEC 61800-3 4...12 kHz shielded motor cable <50 m
Product certifications NOM
UL
GOST
C-Tick
CSA
Vibration resistance 1 gn 13…200 Hz)EN/IEC 60068-2-6
1.5 mm peak to peak 3…13 Hz) - drive unmounted on symmetrical DIN rail - EN/IEC 60068-2-6
Shock resistance 15 gn 11 ms EN/IEC 60068-2-27
Relative humidity 5…95 % without condensation IEC 60068-2-3
5…95 % without dripping water IEC 60068-2-3
Ambient air temperature for storage -25…70 °C
Ambient air temperature for operation -10…40 °C protective cover from the top of the drive removed
40…60 °C with current derating 2.2 % per °C
Operating altitude > 1000...2000 m with current derating 1 % per 100 m
<= 1000 m without
Offer Sustainability
Status održive ponude Proizvod Green Premium
Uredba REACh
print Izjava REACh
Direktiva EU RoHS Proaktivna sukladnost (proizvod izvan zakonskog okvira direktive EU RoHS)
print Izjava EU RoHS
Bez žive Da
Informacije o RoHS izuzeću
print Da
Propis RoHS za Kinu
print Izjava RoHS za Kinu
Izjava o očuvanju okoliša
print Ekološki profil proizvoda
Profil cirkularnosti
print Informacije o kraju vijeka trajanja
WEEE Proizvod se na tržištima EU mora odlagati u skladu sa specifičnim propisima o prikupljanju otpada; nikako se ne smije odlagati s komunalnim otpadom.
Contractual warranty
Jamstvo 18 months